Research use resources

Melanotan I lab report: what to check on a Melanotan I COA

Two Prestige research vials, one in front of the other

Melanotan I, also known by the name afamelanotide, is a synthetic peptide of 13 amino acids. It is the same chain as alpha-melanocyte stimulating hormone (alpha-MSH) with two deliberate changes, and both of them matter when you read its lab report: one of them can’t be seen by mass spec at all. This guide covers what a Melanotan I certificate of analysis (COA) should show and what to check first. For the basics of any report, see How to read a peptide lab report.

The short version

Purity (HPLC)One main peak with no large peak right beside it. 98% or higher is the usual standard.
Identity (mass spec)A measured mass that matches Melanotan I, both end caps included.
ContentMilligrams of Melanotan I in the vial, compared with the 10mg on the label.
Melanotan I, not IIA straight 13 amino acid chain, not the shorter ringed Melanotan II.

What Melanotan I is, chemically

Melanotan I is a straight chain of 13 amino acids with a cap at each end: an acetyl group (Ac) on the first amino acid and an amide (NH2) on the last. It follows the sequence of alpha-MSH except at two positions. At position 4, methionine is replaced by norleucine (Nle), which has the same shape but no sulfur, so it can’t oxidize. At position 7, the usual phenylalanine is replaced by its mirror image, D-phenylalanine.

AcSerTyrSerNle4GluHisD-Phe7ArgTrp9GlyLysProVal
Melanotan I, thirteen amino acids, acetyl at the start and an amide (NH2) at the end. Norleucine (position 4) and D-phenylalanine (position 7), the two changes from alpha-MSH. Tryptophan sits at position 9.
Reference factMelanotan I, as on our product page
Other nameAfamelanotide
SequenceAc-Ser-Tyr-Ser-Nle-Glu-His-D-Phe-Arg-Trp-Gly-Lys-Pro-Val-NH2
ShapeLinear (a straight chain, no ring)
FormFreeze dried (lyophilized) powder, 10mg vials

Melanotan I and Melanotan II are different peptides

The names are close, and labels and reports sometimes mix them up. Melanotan II is shorter (seven amino acids) and closed into a ring; Melanotan I is the full straight 13 amino acid chain. They weigh very different amounts, so the mass spec line on a report tells them apart at once. Check that the report names Melanotan I (or afamelanotide) and that the sequence is the linear one above. Our Melanotan II lab report guide covers the other one.

Purity: the peak only HPLC can show

Purity comes from HPLC: the sample runs through a column, a UV detector draws a peak for each component, and purity is the main peak’s area as a share of every peak. On a Melanotan I trace, the small peaks worth knowing are:

  • The wrong mirror image at position 7. If ordinary phenylalanine ends up where D-phenylalanine should be, the result has exactly the same mass as Melanotan I. Mass spec can’t see it. Only a separate peak on the HPLC trace shows it, which is why the trace matters as much as the identity line.
  • Oxidized tryptophan. Tryptophan (position 9) can react with oxygen and light over time, adding a little mass. Norleucine was chosen partly to remove the other oxidation spot of the natural hormone.
  • Chains missing an amino acid, left from a synthesis step that didn’t finish, and versions missing the acetyl cap.

Identity: what mass spec confirms

Mass spectrometry weighs the main peak. A measured mass that matches Melanotan I confirms the chain, the acetyl cap and the end amide are all there; a missing cap or an amide that became an acid would each shift the mass. A 13 amino acid peptide with arginine, lysine and histidine often appears in the spectrum carrying two or three charges at once, so a spectrum can show several signals that all belong to the same molecule.

Content: milligrams, not percent

Content is how many milligrams of Melanotan I the lab measured in the vial. The powder also holds salts and a little water, so content and purity are separate numbers. A report that gives content per vial answers the question the label asks. More in Purity vs content.

Our Melanotan I reports

Melanotan I is new on our site. Independent lab reports are linked on its product page as they come in; none is posted yet. Contact us and we will send the documentation for the lot you receive. When a report is posted, the checks below are the ones to run on it.

Checking a Melanotan I report, step by step

  1. Name and sequence: Melanotan I or afamelanotide, the linear 13 amino acid chain, not Melanotan II.
  2. Purity from HPLC, 98% or higher, with no large peak right beside the main one.
  3. Identity from mass spec: the report states that the measured mass matches Melanotan I.
  4. Content in milligrams, close to or above the 10mg on the label.
  5. The lab and report number, matching the report linked on the product page.

Common questions

Are Melanotan I and afamelanotide the same?

Yes, two names for the same 13 amino acid peptide. Reports may use either; the sequence is what to match.

Why can’t mass spec alone confirm Melanotan I?

Because D-phenylalanine and ordinary phenylalanine weigh exactly the same. Mass spec confirms the chain; the HPLC trace is what shows the version with the wrong mirror image.

Where will the Melanotan I report be?

On the Melanotan I product page under Specifications & documentation, and on our research materials page, which lists every report.