Research use resources

5-Amino-1MQ lab report: what to check on a 5-Amino-1MQ COA

A Prestige research vial in a soft studio light

5-Amino-1MQ is sold beside research peptides, but it isn’t one. It is a small molecule: two fused rings with an amino group and a methyl group, about a tenth the size of a typical research peptide. That changes what its lab report should look like. There is no amino acid sequence to match, and the identity tests that suit a small molecule differ from the ones used for peptides. This guide covers what a 5-Amino-1MQ certificate of analysis (COA) should show and what to check first. For the basics of any report, see How to read a peptide lab report.

The short version

Purity (HPLC)One main peak, with the wavelength named. 98% or higher is the usual standard.
IdentityMass spec, NMR or both, stating the result matches 5-Amino-1MQ.
ContentMilligrams in the vial compared with the label (10mg or 50mg).
The saltThe report should say which salt form was tested, or that the amount is given for the active part.

What 5-Amino-1MQ is, chemically

The full name is 5-amino-1-methylquinolinium. Quinoline is a pair of fused six sided rings, one of them holding a nitrogen. In 5-Amino-1MQ that nitrogen carries a methyl group, which gives the molecule a permanent positive charge, and an amino group sits at position 5 on the other ring. Because it is charged, it is always supplied as a salt: the positive molecule paired with a negative ion.

N+CH3NH2methyl on the ring nitrogen:a fixed plus chargeamino groupat position 5
A simplified drawing, not to scale. Two fused rings (a quinoline), an amino group at position 5, and a methyl group on the ring nitrogen.
Reference fact5-Amino-1MQ, as on our product page
Full name5-Amino-1-methylquinolinium
TypeSmall molecule (a quinolinium salt), not a peptide
Sizes10mg and 50mg vials

Purity: a small molecule on HPLC

Purity still comes from HPLC: the sample runs through a column, a UV detector draws a peak for each component, and purity is the main peak’s area as a share of every peak. Two things are different from a peptide trace:

  • A strong UV signal. The ring system absorbs ultraviolet light well, so the detector can read it at a longer wavelength than the 214 nm used for most peptides. Either is fine as long as the report names it.
  • Different small peaks. A peptide trace shows chains missing an amino acid. A small molecule trace shows leftovers from its synthesis instead: the starting quinoline before the methyl was added, or a related ring compound. They tend to sit close to the main peak.

Because the molecule is charged and water friendly, a good method has to hold it on the column long enough to separate it from the solvent front. A main peak sitting right at the start of the run is hard to measure cleanly.

Identity: mass spec, NMR or both

For peptides, mass spectrometry is the usual identity test. A small molecule can also be checked by nuclear magnetic resonance (NMR), which reads the hydrogens around the rings and shows where the amino and methyl groups sit. That matters here, because a compound with the amino group at another position on the ring would weigh exactly the same. Mass spec confirms the weight; NMR confirms the arrangement. A report should state that the result matches 5-Amino-1MQ, the compound named on it.

Published work has used liquid chromatography with tandem mass spectrometry to measure 5-amino-1-methylquinolinium in laboratory samples, which shows how specific these methods can be.

Content and the salt question

Content is how many milligrams the lab measured in the vial. With a salt, there is a detail to check: the weight of the powder includes the negative ion paired with the molecule. A report can give the amount of the whole salt or of the active part alone, and the two numbers differ. A clear report says which one it gives, so the number can be compared with the label. For why content and purity are separate numbers at all, see Purity vs content.

Our 5-Amino-1MQ reports

5-Amino-1MQ is new on our site. Independent lab reports are linked on its product page as they come in; none is posted yet. Contact us and we will send the documentation for the lot you receive. When a report is posted, the checks below are the ones to run on it.

Checking a 5-Amino-1MQ report, step by step

  1. The name: 5-Amino-1MQ or 5-amino-1-methylquinolinium.
  2. Purity from HPLC, 98% or higher, with the wavelength named and the main peak clear of the solvent front.
  3. Identity from mass spec, NMR or both, stating a match to 5-Amino-1MQ.
  4. Content in milligrams, close to or above the label, with the salt form or basis stated.
  5. The lab and report number, matching the report linked on the product page.

For keeping sealed vials of powder in good condition, see How to store lyophilized peptides; the same rules (cold, dry, dark) suit a small molecule powder. For what to ask any seller, see our supplier checklist.

Common questions

Is 5-Amino-1MQ a peptide?

No. It is a small molecule, a quinolinium salt. It is often sold alongside research peptides, but its report has no sequence to match.

Why does the salt form matter on a report?

Because the powder’s weight includes the paired ion. The amount of the whole salt and the amount of the active part are different numbers, so a report should say which one it gives.

Where will the 5-Amino-1MQ report be?

On the 5-Amino-1MQ product page under Specifications & documentation, and on our research materials page, which lists every report.